Restore 12X Stain & Sealant FAQs

Restore 12X Stain & Sealant FAQs



  • 6.

    What surfaces can I apply Restore 12X Transparent Stain & Sealant to?

    Wood:  Restore 12X Transparent Stain & Sealant should only be applied on structurally sound wood surfaces. 

    NOT FOR USE ON:   Concrete, composite decking, fiberglass, tile, and metal surfaces.  These surfaces will not allow for proper adhesion. Do not use on driveways, garages, or other areas with vehicular traffic.
  • 7.

    Can I use Restore 12X Transparent Stain & Sealant on concrete surfaces?

    No.  Restore 12X Transparent Stain & Sealant is not for use on any concrete surfaces. Do not use on driveways, garages, or other areas with vehicular traffic.
  • 8.

    Can I use Restore 12X Transparent Stain & Sealant on my composite decking material?

    No.  Restore 12X Transparent Stain & Sealant cannot be used on composite decking material.
  • 9.

    Can Restore 12X Transparent Stain & Sealant be used on vertical surfaces?

    Yes.  Restore 12X Transparent Stain & Sealant can be used on both vertical and horizontal surfaces.
  • 10.

    Do I need to prepare my deck before applying Restore 12X Transparent Stain & Sealant?

    YES!  REGARDLESS OF AGE OR SURFACE CONDITION, FAILURE TO FOLLOW THIS PREPARATION METHOD WILL RESULT IN POOR ADHESION AND POSSIBLE COATING FAILURE.  NEW WOOD DECKS NEED TO WEATHER AT LEAST SIX MONTHS BEFORE APPLICATION. 

     

    PREPARATION WITH RESTORE DECK STRIPPER

     

    Step 1 – Remove existing Stain/Sealer:

    Previously applied coatings need to be removed for two very important reasons; first stains do not adhere well to one another and second the old finish will block the new finish from penetrating the wood.  If the old stain or sealant is peeling, it will pull your new coating up as well.  The new topcoat will not lock down and seal the old topcoat.  Even if you have not recoated your deck in many years and it looks like there is no stain or sealant left on the deck, you must complete this step.    Previously applied stains and sealants may be present on the deck and are not always visible and they will prevent the new topcoat from properly adhering to the wood. 

     

    Strip the surface using a deck brush and the Restore Deck Stripper.  Apply the deck stripper to the deck and scrub it into the wood with a deck brush.  Let it sit for 15 minutes, then power wash it off completely.  Follow all of the instruction on the back of the Restore Deck Stripper label before proceeding. Next sand the entire deck using 50 or 60 grit sand paper.  This will open the pores of the wood and create a textured surface that is easier for the coating to adhere to.

     

    Step 2 – Clean:

    Clean the surface using a deck brush and the Restore Deck & Concrete Cleaner.  The surface must be completely clean and free of dirt, grease, mildew and organic growth to ensure product bonding and adhesion.  For best results use a pressure washer, in addition to the Restore Deck & Concrete Cleaner, to remove embedded dirt and grime. (Use at a low setting 500-1200 PSI.  Do not use high pressure as it may harm the wood.) For mildew and other organic growth use a diluted solution of household bleach (3 parts water to 1 part bleach) applied to the surface before cleaning.  Loose paint needs to be scraped and removed from the surface.

     

    Step 3 – Test Surface for Application:

    AFTER CLEANING THE SURFACE YOU MUST CONDUCT A SPLASH TEST TO ASSURE THE OLD COATING IS FULLY REMOVED FOR PROPER ADHESION OF THE NEW TOPCOAT.  PREVIOUSLY APPLIED SEALERS may be present on the deck and are not always visible. Conduct a splash test by sprinkling water on multiple areas of the surface.  Check at least 4 areas, or more for larger areas. Be sure to check both high traffic areas such as walkways and non-traffic areas. If the water absorbs rapidly into the surface, the surface is ready to be coated.  If the water beads, puddles or is not absorbed, the surface is sealed and not ready to coat.  If any part of the surface is not absorbing the water, use the Restore Deck Stripper and Sand using 50 or 60 grit sand paper again in that section. Clean again with a brush and Restore Deck & Concrete Cleaner and conduct the splash test again.  Continue this process until the water is absorbed by the wood in all test areas.  Let the surface dry completely before application.  Failure to follow this process will result in poor adhesion and possible coating failure.

     

    Step 4 – Light Repairs:

    Raised nail heads and/or screws should be secured using a hammer or a screwdriver.  Remove loose splinters and replace severely damaged or rotting boards.  Fill larger cracks using RESTORE CRACK FILLER or similar acrylic, non-silicone filler.  Allow to dry.